Hardware Error (HW Error)
A Hardware Error (HW Error) in ASIC mining is an error detected when mining hardware produces a computational result that does not pass the expected validity check. HW errors are commonly associated with ASIC chip instability and can be caused by excessive frequency, insufficient voltage, overheating, power instability, or hardware problems. Mining firmware often records HW errors as part of its diagnostic statistics.
Hardware Error (HW Error) Explained in Simple Terms
Bitcoin ASIC miners perform enormous numbers of SHA-256 calculations every second.
The ASIC hardware should perform these calculations correctly.
Sometimes, however, a chip produces an incorrect result.
When the mining software or firmware detects that the result is invalid, it may record a hardware error.
The process can be simplified as:
ASIC Calculates Hash → Result Checked → Invalid Result Detected → HW Error Recorded
Think of an ASIC chip as a calculator performing billions or trillions of operations.
If the calculator occasionally produces the wrong answer because it is running too fast or does not have sufficient electrical stability, that incorrect result represents the basic idea behind an HW error.
How Hardware Error (HW Error) Works
A simplified HW error process works as follows:
Mining Work Is Assigned
The ASIC receives data to hash.ASIC Chips Perform SHA-256 Calculations
Chips search through possible hash values.A Result Is Returned
The ASIC reports a result to the miner's control system.The Result Is Verified
Firmware or mining software checks whether the returned result is valid.An Incorrect Result Is Detected
If validation fails because of computational instability, an HW error may be recorded.
Repeated errors can indicate that one or more ASIC chips are operating outside a stable range.
Example of Hardware Error (HW Error) in Practice
Suppose an ASIC miner operates normally using factory settings.
The operator installs tuning firmware and increases chip frequency to obtain additional hash rate.
Initially, the miner appears to produce more TH/s.
However, its diagnostic interface begins showing rapidly increasing HW errors.
The likely sequence is:
Higher Frequency → Reduced Stability → Incorrect Calculations → More HW Errors
The operator lowers the frequency slightly.
Afterward:
HW errors decrease
temperatures become more stable
power consumption falls
effective pool hash rate becomes more consistent
The slightly lower frequency may therefore produce better real-world mining performance.
Why Hardware Errors Matter
HW errors can indicate that mining hardware is performing work that cannot contribute successfully to mining.
Monitoring them helps operators:
identify unstable ASIC chips
evaluate tuning profiles
diagnose hashboard problems
detect excessive overclocking
identify undervolting instability
investigate thermal problems
improve effective hash rate
avoid wasting electricity on incorrect computation
HW errors are most useful when analyzed together with other miner statistics.
What Causes Hardware Errors?
Several conditions can cause or contribute to HW errors.
Excessive Frequency
ASIC chips may become unstable when their operating frequency is too high.
The relationship can become:
Frequency Too High → Timing Instability → Incorrect Results → HW Errors
This is particularly common when testing aggressive overclocking profiles.
Insufficient Voltage
Higher frequencies generally require sufficient voltage for reliable chip operation.
If voltage is too low for the selected frequency:
Insufficient Voltage → Unstable ASIC Operation → HW Errors
This can occur during aggressive undervolting.
High Temperature
Excessive chip temperatures can reduce operating stability.
A miner that is stable in cool conditions may begin producing more errors when ambient or die temperatures increase.
Power Instability
Problems with power delivery can interfere with ASIC operation.
Potential sources include:
PSU problems
unstable voltage regulation
damaged connectors
board-level power issues
ASIC Chip Problems
A damaged or degraded ASIC chip may produce abnormal numbers of errors even when other chips on the same board remain stable.
Hashboard Problems
Electrical or communication problems on a hashboard can also contribute to abnormal hardware behavior.
Hardware Error Count vs Hardware Error Rate
These metrics are related but different.
HW Error Count
Shows:
the number of hardware errors recorded.
This value may continuously increase as the miner operates.
HW Error Rate
Shows:
errors relative to the amount of work performed, time, or another reference metric.
This makes it easier to compare stability across different operating periods.
For example, 100 errors over several months have a very different meaning from 100 errors within a few minutes.
Raw error count should therefore be interpreted together with uptime and workload.
Hardware Errors and Frequency Scaling
Frequency scaling changes the operating clock rate of ASIC chips.
Increasing frequency generally increases potential hash rate.
However, every chip has practical stability limits.
The relationship may look like:
Frequency ↑ → Hash Rate ↑ → Stability Margin ↓
If frequency exceeds a stable operating point, HW errors can increase.
The optimal setting is therefore not necessarily the maximum frequency the ASIC can briefly reach.
Hardware Errors and Voltage Scaling
Voltage and frequency should be considered together.
A chip operating at a higher frequency may require additional voltage.
A chip operating at a lower frequency may remain stable at reduced voltage.
The goal is to find an appropriate operating point:
Frequency + Voltage → Stable Hashing
Too little voltage can increase errors.
Increasing voltage unnecessarily, however, increases power consumption and heat.
Therefore, simply raising voltage is not a universal solution for HW errors.
Hardware Errors and ASIC Overclocking
Overclocking is one of the situations where HW error monitoring becomes particularly important.
An aggressive profile may show:
higher configured frequency
higher local hash rate
higher power consumption
higher temperatures
more HW errors
The additional theoretical performance must be compared with useful pool-side performance.
If errors increase substantially, reducing the overclock may provide better overall results.
Hardware Errors and Undervolting
Undervolting reduces ASIC operating voltage to improve energy efficiency.
Successful undervolting can provide:
lower power consumption
lower heat output
improved J/TH
But if voltage becomes insufficient:
Voltage Too Low → Chip Instability → HW Errors Increase
Monitoring HW errors is therefore important when searching for efficient voltage-frequency combinations.
Hardware Errors and ASIC Temperature
Temperature can affect chip stability.
Operators may notice patterns such as:
Low Temperature → Stable Operation
Temperature Rises → HW Errors Increase
If errors appear primarily during hot periods, the underlying problem may involve:
insufficient airflow
high ambient temperature
dust buildup
fan problems
aggressive tuning with limited thermal margin
Temperature history can help confirm the relationship.
Hardware Errors vs Rejected Shares
HW errors and rejected shares should not be treated as the same metric.
Hardware Error
Usually originates:
inside the mining hardware or its computational process.
It indicates:
an incorrect or failed ASIC calculation detected locally.
Rejected Share
Occurs when:
the mining pool rejects submitted work.
Possible reasons include:
stale work
invalid work
communication issues
other pool-specific rejection reasons
Some hardware instability can eventually contribute to invalid submitted work, but not every rejected share is caused by an HW error.
Hardware Errors vs Stale Shares
A stale share is generally valid work that arrives after the pool has already moved to newer mining work.
This is commonly associated with:
network latency
slow job switching
temporary connectivity problems
The difference can be summarized as:
HW Error → Computational Problem
Stale Share → Timing Problem
A miner with many stale shares may have perfectly healthy ASIC chips.
Hardware Errors vs Invalid Shares
An invalid share is work submitted to a pool that fails the pool's validity requirements.
An HW error is usually detected locally before or during the miner's internal processing.
Although unstable hardware can potentially contribute to invalid work, the metrics exist at different layers.
Therefore:
HW Error ≠ Automatically an Invalid Share
Firmware and pool implementations can also report these statistics differently.
Hardware Errors and Effective Hash Rate
A miner can display a high configured or local hash rate while still operating inefficiently.
Consider two profiles:
Profile | Local Hash Rate | HW Errors | Stability |
Standard | Moderate | Low | Stable |
Aggressive | Higher | High | Unstable |
The aggressive profile may look better based only on local TH/s.
But if instability reduces accepted work at the pool, its real advantage may be much smaller.
Operators therefore compare:
local hash rate
HW errors
accepted shares
rejected shares
pool-side hash rate
power consumption
Hardware Errors and ASIC Diagnostics
HW errors are an important diagnostic signal, but they rarely identify the cause by themselves.
Suppose errors suddenly increase.
The operator can investigate:
Has ASIC frequency changed?
Has voltage changed?
Has die temperature increased?
Has ambient temperature increased?
Is the PSU operating normally?
Are errors concentrated on one hashboard?
Are specific ASIC chips unstable?
Did the problem begin after a firmware change?
This helps narrow the problem from a general error statistic to a specific cause.
Per-Chip Hardware Errors
Some ASIC firmware provides more granular information about chip performance.
This can help identify whether errors are:
distributed across the miner
concentrated on one hashboard
associated with individual ASIC chips
If only a small number of chips are unstable, advanced tuning systems may reduce their operating frequency while allowing stronger chips to continue at higher settings.
The exact level of control depends on the ASIC hardware and firmware.
Hardware Errors and Autotuning
Autotuning systems can use HW errors as feedback.
A simplified process is:
Set Frequency/Voltage → Test ASIC → Monitor HW Errors → Adjust → Retest
If a chip remains stable, the firmware may continue testing its operating range.
If errors increase beyond the tuning system's acceptable criteria, the firmware can move back toward a more conservative setting.
HW errors therefore help autotuning software identify stable operating points.
Are Some HW Errors Normal?
A non-zero HW error counter does not automatically mean an ASIC miner is failing.
Mining hardware performs enormous amounts of computation, and firmware implementations differ in how errors are detected and reported.
More useful warning signs include:
rapidly increasing errors
sudden changes from the miner's normal baseline
errors concentrated on particular chips
declining effective hash rate
increased errors after tuning changes
errors correlated with high temperatures
The acceptable level should therefore be evaluated according to the specific ASIC model, firmware, and operating conditions.
How to Reduce Hardware Errors
Depending on the underlying cause, operators may:
reduce ASIC frequency
correct voltage settings
improve cooling
reduce aggressive overclocking
verify PSU operation
inspect power connections
check hashboard condition
review firmware configuration
retune unstable chips
The appropriate solution depends on diagnostics.
Changing random settings without identifying the cause can create additional instability.